Methods of determination of frictional resistances in sheet metal forming of car body sheets
DOI:
https://doi.org/10.24136/atest.2018.170Keywords:
frictional resistances, sheet metal, car bodyAbstract
The friction phenomenon existed in almost all plastic working processes, in particular sheet metal forming, is a complex function of the material's properties, parameters of the forming process, surface topography of the sheet and tools, and lubrication conditions. During the stamping of the drawpieces there are zones differentiated in terms of stress and strain state, displacement speed and friction conditions. This article describes the methods for determining the value of the coefficient of friction in selected areas of sheet metal and presents the drawbacks and limitations of these methods.
Downloads
References
Bay N., Olsson D. D., Andreasen J. L., Lubricant test methods for sheet metal forming, “Tribology International” 2008, vol. 41.
Bhushan B., Contact mechanics of rough surfaces in tribology: multiple asperity contact, “Tribology Letters” 1998, vol. 4.
Guillon O., Roizard X., Belliard P., Experimental methodology to study tribological aspects of deep drawing – application to aluminium alloy sheets and tool coatings, “Tribology International” 2001, vol. 34.
Jurkovic M., Jurkovic Z., Buljan S., The tibological state test in metal forming processes using experiment and modelling, “Journal of Achievements in Materials and Manufacturing Engineering” 2006, vol. 18.
Lee B. H., Keum Y. T., Wagoner R. H., Modeling of the friction caused by lubrication and surface roughness in sheet metal forming, “Journal of Materials Processing Technology” 2000, vol. 130-131.
Matuszak A., Determination of the frictional properties of coated steel sheets, “Journal of Materials Processing Technology” 2000, vol. 106.
Roizard X., Raharijaona F., von Stebut J., Belliard P., Influence of sliding direction and sliding speed on the microhydrodynamic lubrication component of aluminium mill-finish sheets, “Tibology International” 1999, vol. 32.
Świątkowski K., Sposoby oceny wielkości tarcia na powierzchniach kontaktu niemetalicznego materiału modelowego i narzędzia, „Obróbka Plastyczna Metali” 2000, nr 7, 2000.
Trzepieciński T., Analysis of the friction influence on change of surface topography in strip drawing test, “Tribologia” 2013, tom 44.
Le H. R., Sutcliffe M. P. F., Measurements of friction in strip drawing under thin film lubrication, “Tribology International” 2002, vol. 35.
Littlewood M., Wallace J. F., The effect of surface finish and lubrication on the fictional variation involved in the sheet-metal-foming process, “Sheet Metal Industry” 1964, vol. 41.
Zhang S., Hodgson P. D., Duncan J. L., Cardew-Hall M. J., Kalyanasundaram S.: Effect of membrane stress on surface roughness changes in sheet forming, “Wear” 2002, vol. 253.
Trzepieciński T., Wpływ odkształcenia plastycznego blachy na zmianę oporów tarcia w procesie tłoczenia, „Rudy i Metale Nieżelazne” 2009, vol. 54.
Lovell M. R., Deng Z., Characterization of interfacial friction in coated sheet steel: influence of stamping process parameters and wear mechanisms, “Tribology International” 2002, vol. 35.
Wagoner R. H., Wang W., Sriram S., Development of OSU formability test and OSU friction test, “Journal of Materials Processing Technology” 1994, vol. 45.
Nine H. D., Draw bead forces in sheet metal forming, Proceedings of a Symposium on Mechanics of Sheet metal Forming: Behaviour and Deformation Analysis, Plenum Press, Warren 1978.
Samuel M., Influence of dawbead geometry on sheet metal forming, “Journal of Materials Processing Technology” 2002, vol. 122.
Hirpa G. Lemu, Trzepieciński T., Numerical and experimental study of the frictional behaviour in bending under tension test, “Strojniski Vestnik - Journal of Mechanical Engineering” 2013, vol. 59 (2013).
Skarpelos P., Morris Jr J. W., The effect of surface morphology on friction during forming of electrogalvanized sheet steel, “Wear” 1997, vol. 212.
Trzepieciński T., Badania oporów tarcia wywołanych działaniem progów ciągowych w procesie kształtowania blach, „Rudy i Metale Nieżelazne” 2010, tom 55.
Kim H., Han S., Yan Q., Altan T., Evaluation of tool materials, coatings and lubricants in forming galvanized advanced high strength steels (AHSS), “CIRP Annals - Manufacturing Technology” 2008, vol. 57.
Zmitrowicz A., Wear patterns and laws of wear - a review, “Journal of Theoretical Applied Mechanics” 2006, vol. 44.
